curva y dimensiones equipo-flowserve.pdf
TRANSCRIPT
-
8/10/2019 Curva y dimensiones equipo-FLOWSERVE.pdf
1/4
WinPROS+ V3.3.3
0 10 20 30 40
Capacity - m3/h
0
50
100
150
200
250
300
350
400
450
500
Hea
d-m
0
5
10
15
20
25
30
35
40
45
50
Efficienc
y
Efficiency
NPSHr
2.00
4.00
NPSHr-m
MCSF400.0 mm Maximum
314.5 mm Rated
300.0 mm Minimum
0
20
40
60
80
Power-kW
Power Viscous curve plottedViscosity 10.0 cP
Viscous corrections :
CQ : 0.99
CH : 1.00
CE : 0.93
Customer : Pump size & type : 2 HED 16
Item number : TEPSI A C RS Based on curve no. : 2 HED 16-LL
Service : Bateria Number of stages : 2
Vendor reference : 5765-W0000 Capacity : 19.0 m3/h Specific gravity : 0.950
Date : January 11, 2011 Head : 200.00 m Pump speed : 2950 rpm
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS, CAPACITY, HEAD, AND EFFICIENCY.
-
8/10/2019 Curva y dimensiones equipo-FLOWSERVE.pdf
2/4
Hydraulic Datasheet
0.950
-
Construction : API-610 10th Edition
Test tolerance : API-610 10th Edition
Driver Sizing : API 610
Seal configuration : Single Seal
Customer : Pump / Stages : 2 HED 16 / 2
Customer reference : Based on curve no. : 2 HED 16-LL
Item number : TEPSI A C RS Vendor reference : 5765-W0000
Service : Bateria Date : January 11, 2011
Operating Conditions Materials / Specification
Capacity : 19.0 m3/h Material column code : A8
Water Capacity (CQ=0.99) : 19.2 m3/h Pump specification :
Normal capacity : - Other Requirements
Total Developed Head : 200.00 m
Water head (CH=1.00) : 200.00 m
NPSH available (NPSHa) : Ample
NPSHa less NPSH margin : -
Maximum suction pressure : 0.0 kg/cmg
Liquid
Liquid type : Other
Temperature / SG : 55 C /
Solid Size - Actual / Limit : -
Viscosity / Vapor pressure : 10.0 cP /
Performance
Hydraulic power : 9.82 kW Impeller diameter
Pump speed : 2950 rpm Rated : 314.5 mm
Efficiency (CE=0.93) : 18.3 % Maximum : 400.0 mm
Minimum : 300.0 mm
NPSH required (NPSHr) : 3.0 m Suction specific speed : 5110 US units
Rated power : 53.7 kW Minimum continuous flow : 5.9 m3/h
Maximum power : 57.9 kW Maximum head @ rated dia : 277.0 m
Driver power : 75.0 kW / 101 hp Flow at BEP : 18.1 m3/h
Casing working pressure : 27.6 kg/cmg Flow as % of BEP : 105.2 %
(based on shut off @ cut dia) Efficiency at normal flow : -
Maximum allowable : 79.6 kg/cmg Impeller dia ratio (rated/max) : 78.6 %
Hydrostatic test pressure : 122.4 kg/cmg Head rise to shut off : 38.5 %
Est. rated seal chamb. press. : - Total head ratio (rated/max) : 52.0 %
/ 0.00 mm
350
400
450
500
35
40
45
50
MCSF400.0 mm Maximum
0
20
40
60
80
Power-
kW
PowerViscous curve plotted
Viscosity 10.0 cP
Viscous corrections :
CQ : 0.99
CH : 1.00
CE : 0.93
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS, CAPACITY, HEAD, AND EFFICIENCY.
-
8/10/2019 Curva y dimensiones equipo-FLOWSERVE.pdf
3/4
393.0 135.0 568.0 230.0 230.0
460.0
400.0
300
950 2356.0
960
80
690
20.0
600# RF Top
600# RF Top
Cast Iron
-
3 50
6.80
: -
: -
Customer : Pump / Stages : 2 HED 16 / 2
Customer reference : Based on curve no. : 2 HED 16-LL
Item number : TEPSI A C RS Vendor reference : 5765-W0000
Service : Bateria Date : January 11, 2011
Construction Driver Information
Nozzles Size Rating Face Pos'n Manufacturer : Marelli
Power : 75.0 kW / 101 hpSuction 3 inch
Service factor ( req'st / act) : 1.00 / 1.00Discharge 2 inch Speed : 3000 rpm
Orientation : Horizontal/ Mounting -/Casing mounting : Center-lineDriver Type : IECCasing split : RadialFrame-size / material : 280S /Impeller type : ClosedEnclosure : TEFC EEx-dBearing Type (Rad/Thr) : - /Hazardous area class : -
Bearing lubrication : FlingerExplosion 'T' rating : -Rotation (view from cplg) : CCW per Hyd. InstituteVolts / Phase / Hz : 380 / /
Materials Amps-full load/locked rotor : 142.00 /
Motor starting : Direct on line (DOL)Casing : ASTM A351 CF8M
Insulation : FImpeller : ASTM A351 Gr.CF8M
Temperature rise : -Case wear ring : A743 CF10 S MnN
Motor mounted by : FPDImpeller wear ring : A743 CG6MMN (230HB)
Inducer : -Seal, Gland and Piping
Shaft : ASTM A276-316L
Arrangement : -Sleeve : ASTM A276 316LSize : -
Baseplate, Coupling and GuardManufacturer : -/ Type -/
Material code (Man'f/API) -/Baseplate type : Fabricated steel
Internal neck bushing : -Baseplate material : Steel plate
Gland material : -Coupling manufacturer : -
Flush : -Coupling size : 70 HVII
Vent : -Coupling / Shaft guard : Aluminium; No Spark.
Drain : - Weights (Approx.)
Auxiliary sealing device : -
Bareshaft pump(nett) : 798.0 kg Seal flush plan : None
Baseplate(nett) : - Seal flush material : -
Driver(nett) : 464.0 kg Aux seal flush plan : None
Shipping gross weight/vol. -/ Aux seal flush material : -
Construction Datasheet
-
8/10/2019 Curva y dimensiones equipo-FLOWSERVE.pdf
4/4
393.0 135.0 568.0 230.0 230.0
460.0
400
.0
300
950 2356.0
960
280
690
4150
720
.0
220
1235
617.5 617.5
500
.01120
.0
850.0
Customer :
Item number : TEPSI A C RS
Service : Bateria
Vendor reference : 5765-W0000
Date : January 11, 2011
Pump size & type : 2 HED 16
Pump speed / Stages : 2950 rpm 2
Drawing number
Rev. A
280SDriver power / Frame : 75.0 kW / 101 hp
Volts / Phase / Hz : 380
Full Page GA Drawing
Certified by / Date :
/
Customer PO # :
/
Flow / Head : 19.0 m3/h 200.00 m/
/
/3 50Seal type : -
Seal flush plan : None
All dimensions are in millimeters unless otherwise specified
WinPROS+ V3.3.3Copyright 2004 Flowserve. All rights reserved