habilidad n84 - ajuste apropiado de la cadena en tractores
TRANSCRIPT
-
8/9/2019 Habilidad N84 - Ajuste Apropiado de La Cadena en Tractores
1/5
Operation and Maintenance Manual D8R Track-Type Tractor
Track - Check/Adjust
SMCS - 4170-036
Check the track adjustment. Check the track for wear and for excessive dirt buildup.
1. Move the machine forward. Allow the machine to coast to a stop without the use of the service
Shutdown SI
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8R TRACK-TYPE TRACTOR 9EM
Configuration: D8R Track-Type Tractor 9EM00001-UP (MACHINE)POWERED BY 3406 Engine
Media Number -SEBU6891-02 Publication Date -01/04/1999 Date Updated -12/05/2004
i01032562
Illustration 1 g00479439
Grease is under high pressure.
Grease coming out of the relief valve under pressure can penetrate thebody causing injury or death.
Do not watch the relief valve to see if grease is escaping. Watch thetrack or track adjustment cylinder to see if the track is being loosened.
Loosen the relief valve only one turn.
Página 1 de 5D8R Track-Type Tractor 9EM00001-UP (MACHINE) POWERED BY 3406 Engine(S...
22/02/2005https://sis.cat.com/sisweb/servlet/cat.dcs.sis.controller.techdoc.CSSISFormatTechDocFor...
-
8/9/2019 Habilidad N84 - Ajuste Apropiado de La Cadena en Tractores
2/5
-
8/9/2019 Habilidad N84 - Ajuste Apropiado de La Cadena en Tractores
3/5
If the machine is equipped with a carrier roller, the correct adjustment of dimension (3) and dimension(4) is 65 ± 10 mm (2.6 ± .4 inch).
Loose Track Adjustment
Illustration 3 g00104000
Illustration 4 g00040335
NOTICE
Do not attempt to tighten track when dimension (1) is 142 mm (5.60inch) or more. Contact your Caterpillar dealer for track service orinstructions.
Página 3 de 5D8R Track-Type Tractor 9EM00001-UP (MACHINE) POWERED BY 3406 Engine(S...
22/02/2005https://sis.cat.com/sisweb/servlet/cat.dcs.sis.controller.techdoc.CSSISFormatTechDocFor...
-
8/9/2019 Habilidad N84 - Ajuste Apropiado de La Cadena en Tractores
4/5
1. Remove the access cover.
2. Add multipurpose grease (MPGM) through track adjustment valve (5). Add the MPGM untildimension (2) is correct.
3. Operate the machine back and forth in order to equalize the pressure. Allow the machine to coastto a complete stop. Do not use the brakes.
4. Remeasure dimension (2) .
Tight Track Adjustment
1. Loosen relief valve (6) by one turn of 360 degrees. Allow the grease to escape.
2. Close the relief valve.
3. Add MPGM through track adjustment valve (5). Add grease until dimension (2) is correct.
Illustration 5 g00104001
Illustration 6 g00104002
Página 4 de 5D8R Track-Type Tractor 9EM00001-UP (MACHINE) POWERED BY 3406 Engine(S...
22/02/2005https://sis.cat.com/sisweb/servlet/cat.dcs.sis.controller.techdoc.CSSISFormatTechDocFor...
-
8/9/2019 Habilidad N84 - Ajuste Apropiado de La Cadena en Tractores
5/5
4. Install the access cover.
Bolt Torque for Track Shoes
The torque requirement for track shoe bolts is 650 ± 70 N·m (480 ± 50 lb ft). Tighten the bolts for anadditional 120 degrees. If you are using bolts with a master link, tighten the bolts to a torque of 650 ± 70
N·m (480 ± 50 lb ft). Then, tighten the bolts for an additional 120 degrees.
Copyright 1993 - 2005 Caterpillar Inc.All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 22 15:47:31 UTC-0300 2005
Página 5 de 5D8R Track-Type Tractor 9EM00001-UP (MACHINE) POWERED BY 3406 Engine(S...
22/02/2005h // i / i b/ l / d i ll hd CSSISF T hD F