como armar un chasis de karting
Post on 07-Jul-2018
234 Views
Preview:
TRANSCRIPT
-
8/18/2019 como armar un chasis de karting
1/40
-
8/18/2019 como armar un chasis de karting
2/40
-
8/18/2019 como armar un chasis de karting
3/40
Copyright Notices
Copyright 2011 WcWelding All Rights Reserved.
Any unauthorized transfer of license, use, sharing, reproduction or distributio
hese materials by any means, electronic, mechanical, or otherwise is prohibitedortion of these materials may be reproduced in any manner whatsoever, withoutxpress written consent of the publishers.
Published under the Copyright Laws of the Library Of Congress Of The Untied S
f America, by:
WcWelding.com14525 SW Millikan Way #87946Beaverton, Oregon 97005-2343Legal Notices While all attempts have been make to verify information provided in this publica
either the Author nor the Publishers assumes any responsibility for errors, omissioontradictory interpretation of the subject matter herein.
This publication is not intended for use as a source of business, legal or accoudvice. The Publishers want to stress that the information contained herein maubject to varying state and /or local laws or regulations. All users are advised to reompetent counsel to determine what state and /or local laws or regulations may ao the user’s particular business.
The purchaser or reader of this publication assumes responsibility for the us
hese materials and information. Adherence to all applicable laws and regulations,
ederal and state and local, governing professional licensing business practdvertising and all other aspect of doing business in the US or any other jurisdictioole responsibility of the purchaser or reader. WcWelding.com, assumes no responsiability whatsoever on the behalf of any purchaser or reader of these materials.
The information in this manual/report/book/ebook is true and complete to the
f our knowledge. All recommendations are made without guarantee on the part outhor or publisher, who also disclaim any liability incurred in connection with the ushis material.
-
8/18/2019 como armar un chasis de karting
4/40
MATERIALS REQUIRED: (42 FT) Round Tubing, 1.00” O.D. X .058” wall(2 ½” X 6”) Mild steel sheet, 11 GA (4” X 8”) Mild steel plate, ¼” (4” X 12”) Mild steel sheet, 14 GA (23” X 22”) Mild steel sheet, 16 GA SUGGESTED TOOLS: Tube bender with a bending die for ¾” tubing, 4” be
adius.Hole saw cutting tool (such as a Joint Jigger™ or sim
rand)Hole saw, ¾” diameterBend grinder with ¾” wide grinding wheel.Flat work surface
IMPORTANT NOTES:
This project is intended to be completed using either M
TIG, or Oxy-Acetylene weld processes. However, if either Tr the Oxy processes are used, the weld joints need to
articularly tight. Whenever you make more than one bend in a tube fo
hat must remain flat, pay particular attention to the planehe tube prior to each bend. Otherwise, the tube form mecome unusable. This can be accomplished by adjusting
eight of a take-up table or surface to correspond to
-
8/18/2019 como armar un chasis de karting
5/40
ottom of the tube. This is best done before any bends made, while the tube is resting in the bending die.
The actual plans for the frame follow the steps which
ecessary to building the frame. The images where take ou
ur PDF version of the plans and some measurements ard to read, so what we did was put a URL after each imwith measurements that may be hard to read. I think yond it helpful J
-
8/18/2019 como armar un chasis de karting
6/40
INSTRUCTIONS: Step 1
Referring to the cut list on page one of the drawing, cuength of ¾” X .058 tubing for part number WP-908-2. Step 2 Using a tube bender with a ¾” X 4” bending die, make
ends in the tube to create part number WP-908-2 as shon the drawing. This will be the bottom of the go-kart fra
After all bends are made, this part will be a rectangle. Mure the tube ends are within a 1/16” from each other acing each other in the middle of one of the shorter legs of ectangle, as noted on the drawing.
Step 3 Weld the ends of the tube rectangle together. This should flat weld bead all the way around the tube. Make sure
frame bottom” lays flat on the work surface before and aftes welded.
Step 4 Cut the length of tubing for part number WP-908-3 Step 5
-
8/18/2019 como armar un chasis de karting
7/40
Similar to the above steps, make the necessary bendsreate part number WP-098-3. Step 6
Most hole saw tools will not make long, shallow cuts like nes at theends of part number WP-908-3. This is due to the lim
ravel distance of the hole saw. An effective method reparing these tube ends for the joint is by forming them oench grinder. This is a common method of creating a “Fi
mouth” in the ends of tubing used in aircraft construction. Ione by using a dressing wheel to create a radius to the ff a grinding wheel. The width of the grinding wheel mqual the diameter of the tubing to which the part will matehis case, ¾”.
After the grinding wheel face has been shaped (radiuse
he tube end can be formed by holding the end of a tube at orrect angle while grinding a concave or “fish-mouecessary to create the joint geometry. It is advisable to practice first on a piece of scrap tubing.
ure to work slowly and check the fit often. It won’t take lo
o get a feel for how much to grind. The results can urprisingly good.
Step 7 Cut tubing and make the necessary end cuts for p
umbers WP-908-5, WP-908-6, WP-908-7, WP-908-8, WP-9
-
8/18/2019 como armar un chasis de karting
8/40
, and WP-908-10. Always check the fit of the tube where ths contact with another tube, in other words, at the joints.
Step 9
Place the frame bottom, WP-908-2, on the flat work surfaClamp it in place, or place weights on top so it will not masily. Position a WP-908-10 on one side of the frame bottom
ndicated on the drawing. Make sure this tube is vertical aerpendicular to the long side of the bottom frame. Tack w
n place. Step 10 Repeat on the other side of the frame bottom.
Step 11 Place part numbers WP-908-6, and WP-908-7 between
rame bottom and in the locations indicated on the drawi
-
8/18/2019 como armar un chasis de karting
9/40
Tack weld in place.
Step 12 Place part numbers WP-908-3, WP-908-5, WP-908-8,
WP-908-9 on the frame bottom as indicated on the drawiHold these parts in place with clamps, magnets, or wRecheck placement and fit after they have been securedlace. There should not be more than a 1/16” gap betwarts at the joints.
Step 13 Tack weld each tube at the joints. Make sure the fra
ottom is still flat on the work surface. Complete the welds
-
8/18/2019 como armar un chasis de karting
10/40
ach joint, alternating from one side of the frame to the othe Step 14 Cut a length of tubing and bend according to the drawing
make part number WP-908-4. This is the roll-over bar/sack. Step 15 Position the roll-over bar on the frame according to
rawing. Check the fit at the tube ends. Tack weld in placeoth ends of the tube. Recheck placement and fit and complhe welds.
Step 16 Make part number WP-908-13. Position each part (one a
me) on the frame and check the fit. Tack weld each tubehe correct angle, making sure both parts are in-line with pumber WP-908-6 (front crossmember). The position, placement, and angle of these parts dire
ffect the tracking and steering of the go-kart. Once this
een assured, complete the welds. Step 17 Cut part number WP-908-16 (qty 2) from the 11 GA she
Bend the plates as indicated on the drawing. Note: use the
attern dimensions when cutting the parts out of the sheet.
-
8/18/2019 como armar un chasis de karting
11/40
Step 18 Weld WP-908-16 in place one at a time as indicated on
rawing. The position, placement, and angle of these parts a
ffect the tracking and steering of the go-kart. Special chould be taken to assure they are correct on the frame befnd after welding. Step 19 Cut and prepare the ends of part number WP-908-12 (qty
Cut a length of tube for part number WP-908-11. Step 20 Position these tubes on the frame as indicated on
rawing. Check the joint fit and tack weld in place. Th
omplete the welds. Step 21 From the 16 GA material, cut part number WP-908-17. Pl
his part on the frame and weld in place. To eliminate or av
warping the plate, or causing misalignment, begin by twelding the plate at each corner and in the middle of edge. Step 22
Cut part number WP-908-14 from the ¼” plate mate
-
8/18/2019 como armar un chasis de karting
12/40
-
8/18/2019 como armar un chasis de karting
13/40
-
8/18/2019 como armar un chasis de karting
14/40
Go Kart Frame Plans:
To See A Larger Version Of This Frame Image go to: Copy and Paste this URL Into Yo
Browser.https://reader009.{domain}/reader009/html5/0723/5b55bba2512
http://www.wcwelding.com/images/goframe1.jpg
-
8/18/2019 como armar un chasis de karting
15/40
Side View:
To See A Larger Version Of This Frame Image go to: Copy and Paste this URL Into Yo
Browser.
https://reader009.{domain}/reader009/html5/0723/5b55bba251258/
http://www.wcwelding.com/images/frame-side-view.jpg
-
8/18/2019 como armar un chasis de karting
16/40
Rear View and Front View:
To See A Larger Version Of This Frame Image go to: Copy and Paste this URL Into Yo
Browser.
https://reader009.{domain}/reader009/html5/0723/5b55bba251258/5b
http://www.wcwelding.com/images/frame-rear-front-view.jpg
-
8/18/2019 como armar un chasis de karting
17/40
Top View
To See A Larger Version Of This Frame Image go to: Copy and Paste this URL Into Yo
Browser.
https://reader009.{domain}/reader009/html5/0723/5b55bba251258
http://www.wcwelding.com/images/frame-top-view.jpg
-
8/18/2019 como armar un chasis de karting
18/40
-
8/18/2019 como armar un chasis de karting
19/40
Bottom View:
To See A Larger Version Of This Frame Image go to: Copy and Paste this URL Into Yo
Browser.
https://reader009.{domain}/reader009/html5/0723/5b55bba251258/5
http://www.wcwelding.com/images/frame-bottom-view.jpg
-
8/18/2019 como armar un chasis de karting
20/40
-
8/18/2019 como armar un chasis de karting
21/40
-
8/18/2019 como armar un chasis de karting
22/40
-
8/18/2019 como armar un chasis de karting
23/40
WP-908-3:
To See A Larger Version Of This Frame Image go to: Copy and Paste this URL Into Yo
Browser.
http://www.wcwelding.com/images/WP908-3a.jpg
And
http://www.wcwelding.com/images/WP-908-3b.jpg
And
http://www.wcwelding.com/images/WP-908-3C.jpg
http://www.wcwelding.com/images/WP-908-3C.jpghttp://www.wcwelding.com/images/WP-908-3b.jpghttp://www.wcwelding.com/images/WP908-3a.jpg
-
8/18/2019 como armar un chasis de karting
24/40
-
8/18/2019 como armar un chasis de karting
25/40
WP-908-4:
To See A Larger Version Of This Frame Image go to: Copy and Paste this URL Into YoBrowser.
http://www.wcwelding.com/images/WP-908-4a.jpg
And
http://www.wcwelding.com/images/WP-908-4b.jpg
And
http://www.wcwelding.com/images/WP-908-4c.jpg
http://www.wcwelding.com/images/WP-908-4c.jpghttp://www.wcwelding.com/images/WP-908-4b.jpghttp://www.wcwelding.com/images/WP-908-4a.jpg
-
8/18/2019 como armar un chasis de karting
26/40
-
8/18/2019 como armar un chasis de karting
27/40
WP-908-5, WP-908-6, WP-908-10:
To See A Larger Version Of These Images go to: Copy and Paste this URL Into You
Browser.
http://www.wcwelding.com/images/WP-908-5a.jpg
And
http://www.wcwelding.com/images/WP-908-5b.jpg
And
http://www.wcwelding.com/images/WP-908-10.jpg
http://www.wcwelding.com/images/WP-908-10.jpghttp://www.wcwelding.com/images/WP-908-5b.jpghttp://www.wcwelding.com/images/WP-908-5a.jpg
-
8/18/2019 como armar un chasis de karting
28/40
-
8/18/2019 como armar un chasis de karting
29/40
WP908-6, WP-908-7, WP-908-11:
To See A Larger Version Of These Images go to: Copy and Paste this URL Into You
Browser.
http://www.wcwelding.com/images/WP-908-6.jpg
And
http://www.wcwelding.com/images/WP-908-7.jpg
And
http://www.wcwelding.com/images/WP-908-11.jpg
http://www.wcwelding.com/images/WP-908-11.jpghttp://www.wcwelding.com/images/WP-908-7.jpghttp://www.wcwelding.com/images/WP-908-6.jpg
-
8/18/2019 como armar un chasis de karting
30/40
-
8/18/2019 como armar un chasis de karting
31/40
-
8/18/2019 como armar un chasis de karting
32/40
WP908-12:
To See A Larger Version Of These Images go to: Copy and Paste this URL Into You
Browser.
http://www.wcwelding.com/images/WP-908-12.jpg
http://www.wcwelding.com/images/WP-908-12.jpg
-
8/18/2019 como armar un chasis de karting
33/40
-
8/18/2019 como armar un chasis de karting
34/40
-
8/18/2019 como armar un chasis de karting
35/40
-
8/18/2019 como armar un chasis de karting
36/40
WP-908-16:
-
8/18/2019 como armar un chasis de karting
37/40
Engine Mount Bracket:
To See A Larger Version Of These Images go to: Copy and Paste this URL Into You
Browser.
http://www.wcwelding.com/images/WP-908-15.jpg
And
http://www.wcwelding.com/images/WP-908-15.jpg
-
8/18/2019 como armar un chasis de karting
38/40
http://www.wcwelding.com/images/WP-908-15b.jpg
And
http://www.wcwelding.com/images/WP-908-15c.jpg
http://www.wcwelding.com/images/WP-908-15c.jpghttp://www.wcwelding.com/images/WP-908-15b.jpg
-
8/18/2019 como armar un chasis de karting
39/40
-
8/18/2019 como armar un chasis de karting
40/40
Floor Plate:
To See A Larger Version Of This Image go to: Copy and Paste this URL Into Your Brow
http://www.wcwelding.com/images/Floor-plate.jpg
For More Plan Ideas, Projects, and Tips Go To:
WcWelding.com
http://www.wcwelding.com/http://www.wcwelding.com/images/Floor-plate.jpg
top related